Caterpillar 924Hz Wheel Loader
Units
Dimensions
Dimensions
E
Ground Clearance
1.43ft in
Bucket Pin Height - Maximum Lift
12.33ft in
Carry Height
1.43ft in
Centerline Of Front Axle To Hitch
4.59ft in
Digging Depth
1.65in
Dump Clearance At Maximum Lift - 45 Degrees
9.28ft in
Height - Center Of Axle
2.27ft in
Height - Top Of Exhaust Stack
10.53ft in
Height - Top Of Hood
87.36in
Height - Top Of Rops/Fops
10.59ft in
Length - Rear Axle To Bumper
6.44ft in
Overall Height - Bucket Raised
15.78ft in
Overall Length
22.63ft in
Reach At Maximum Lift And 45 Degrees Dump
2.6ft in
Bucket Clearance-Maximum Lift/Carry
11.26ft in
Wheel Base
9.19ft in
Specifications
Engine
Displacement
403cu in
Net Torque
482lb ft
Peak Torque
496lb ft
Bore
4.2in
Stroke
5in
Rated Net Power
128hp
Sae J1349 (2)
138hp
Iso 9249 (1997) (2)
139hp
Eec 80/1269 (2)
139hp
Sae J1349 (1)
128hp
Iso 9249 (1997) (1)
130hp
Eec 80/1269 (1)
130hp
Maximum Net Power - 1800 Rpm
138hp
Operational
Operating Weight
24180lb
Steering
Steering Angle - Each Direction
40degrees
Minimum Turning Radius - Over Tires
200in
Steering Cylinder, Two, Bore
2.8in
Hydraulic Output At 2300 Engine Rpm And 6900 Kpa (1000 Psi)
27 gal/min
Maximum Working Pressure
3000 psi
Transmission
Forward - 1 (1)
4.2mph
Reverse - 1 (1)
4.2mph
Forward - 1 (2)
2.3mph
2 (2)
4.7mph
3 (2)
12.2mph
4 (2)
24.2mph
Reverse - 1 (2)
2.5mph
2 (3)
5mph
3 (3)
13.2mph
2 (1)
7.6mph
3 (1)
13.5mph
4 (1)
23.9mph
Steering
Steering Articulation
40degrees
Transmission
Standard Transmission Maximum Travel Speeds
23.9mph
Optional Low Speed Transmission Maximum Travel Speeds
24.2mph
Tires
Tread Width
6.2ft in
Size
20.5 R25 Radial (L-3)
Buckets
Bucket Capacities
1.7 m3 - 2.1 m3 2.2 yd3 - 2.7 yd3
Operating Specifications
Static Tipping Load - Full Turn
16844lb
Articulation Angle
40degrees
Reach - Full Lift And 45 Degrees Dump
2.6ft in
Dump Clearance At Full Lift And 45 Degrees Dump Angle
9.3ft in
Service Refill Capacities
Cooling System
8.5gal
Fuel Tank
59.4gal
Crankcase
4.4gal
Hydraulic Tank
18.5gal
Hydraulic System - Including Tank
33gal
Transmission
6.1gal
Front
5.5gal
Rear
5.5gal
Cab
Rops
SAE J1040 MAY94, ISO 3471-1994
Fops
SAE J231 JAN81, ISO 3449-1992 Level II
Loader Hydraulic System
Pump Flow - Implement Pump
40.15 gal/min
Output At 2,300 Engine Rpm And 6900 Kpa (1000 Psi) With Sae 10w Oil At 65 Degreesc (150 Degreesf)
39.5 gal/min
Maximum Working Pressure
3755 psi
Raise
5.2 s
Dump
1.1 s
Lower, Empty, Float Down
2.7 s
Total
9 s
Bore (1)
4.3in
Stroke (1)
29.7in
Bore (2)
4.8in
Stroke (2)
20.5in
Hydraulic Cycle Time
9 Seconds
Relief Pressure - Implement Pump
3755 psi
