Caterpillar 815K Compactor
Dimensions
Dimensions (Approximate)
Ground Clearance
1.23ft in
Ground Clearance - Bumper
2.19ft in
Height - Top Of Beacon
12.95ft in
Height - Top Of Cab Roof
11.98ft in
Height - Top Of Exhaust Pipe
10.97ft in
Height - Top Of Hood
8.42ft in
Hitch To Centerline Of Front Axle
5.5ft in
Length - With Blade On Ground
23.48ft in
Width - Over Wheels
10.64ft in
Wheel Base
10.99ft in
Centerline Of Rear Axle To Bumper
6.53ft in
Turning Radius - Inside Of Push Arms
8.27ft in
Operating Specifications
Maximum Operating Weight (Tier 3/Stage Iiia Equivalent)
48740lb
Maximum Operating Weight (Tier 4 Final/Stage Iv)
49353lb
Specifications
Engine
Net Power
248hp
Displacement
427.8cu in
Bore
4.1in
Stroke
5.3in
Emissions
Meets U.S. EPA Tier 4 Final/EU Stage IV emission standards or meets U.S. EPA Tier 3/EU Stage IIIA equivalent emission standards
Engine Model
Cat C7.1 ACERT: configured for two emissions options
Rated Power (Sae J1349) - Tier 4 Final/Stage Iv
248hp
Rated Power (Net Iso 9249) - Tier 4 Final/Stage Iv
248hp
Gross Power - Sae J1995 - Tier 3/Stage Iiia Equivalent
286hp
Rated Power (Net Iso 9249) - Tier 3/Stage Iiia Equivalent
249hp
Maximum Net Torque - 1,400 Rpm - Tier 4 Final/Stage Iv
899lb ft
Rated Power (Sae J1349) - Tier 3/Stage Iiia Equivalent
249hp
Gross Power - Sae J1995 - Tier 4 Final/Stage Iv
284hp
Gross Power - Iso 14396 - Tier 4 Final/Stage Iv
274hp
High Idle Speed
2270rpm
Low Idle Speed
800rpm
Torque Rise - Tier 4 Final/Stage Iv
52%
Gross Power - Iso 14396 - Tier 3/Stage Iiia Equivalent
275hp
Torque Rise - Tier 3/Stage Iiia Equivalent
26%
Maximum Net Torque - 1,400 Rpm - Tier 3/Stage Iiia Equivalent
749lb ft
Maximum Altitude - Without Derating
9842.6ft in
Operational
Operating Weight
49353lb
Transmission
Transmission Type
Planetary Powershift ECPC
Travel Speeds - Forward - First
4.2mph
Travel Speeds - Forward - Second
7.5mph
Travel Speeds - Reverse - First
4.8mph
Travel Speeds - Reverse - Second
8.5mph
Travel Speeds - Forward - Third
13.2mph
Travel Speeds - Reverse - Third
15mph
Wheels
Outside Diameter
4.7ft in
Drum Diameter
3.4ft in
Drum Width
3.3ft in
Tips Per Wheel
60
Weight
9720lb
Width - Over Drums
10.7ft in
Axles
Front
Planetary Fixed
Rear
Planetary Oscillating
Oscillation Angle
10 degrees
Hydraulic System
Maximum Supply Pressure
2930 psi
Main Relief Pressure
3190 psi
Pump Flow At 2,111 Rpm
23.5 gal/min
Lift Cylinder, Double Acting - Bore And Stroke
101.6 mm 627 mm (4 in 24.7 in)
Tilt Cylinder, Double Acting - Bore And Stroke
101.6 mm 167 mm (4 in 6.6 in)
Brakes
Parking Brake
Drum and Shoe, Spring Applied, Hydraulic Released
Service Refill Capacities
Fuel Tank
132.1gal
Engine Crankcase
5.3gal
Transmission
14.8gal
Differential - Final Drives - Front
17.2gal
Differential - Final Drives - Rear
17.2gal
Note
All non-road Tier 4 Final and Stage IV diesel engines are required to use: Ultra Low Sulfur Diesel (ULSD) fuels containing 15 ppm for EPA and 10 ppm for EU (mg/kg) sulfur or less. Biodiesel blends up to B20 are acceptable when blended with 15 ppm for EPA and 10 ppm for EU (mg/kg) sulfur or less ULSD and when the biodiesel feedstock meets ASTM D7467 specifications. Cat DEO-ULS or oils that meet the Cat ECF-3, API CJ-4, and ACEA E9 specifications are required. Diesel Exhaust Fluid (DEF) that meets all requirements defined in ISO 22241-1.
Cooling System - Tier 4 Final/Stage Iv
21.4gal
Diesel Exhaust Fluid Tank (Tier 4 Final/Stage Iv Only)
4.2gal
Hydraulic Tank Only
19.8gal
Cooling System - Tier 3/Stage Iiia Equivalent
19.3gal
Hydraulic System - Steering
Steering System - Circuit
Closed Center Load Sensing
Steering System - Pump
Piston Variable Displacement
Steering Pressure Limited
4003 psi
Bore
4in
Stroke
23.5in
Maximum System Flow
147 L/min @ 2,111 rpm (38.8 gal/min @ 2,111 rpm)
Vehicle Articulation Angle
84 degrees
Blades
Height - Including Cutting Edge
2.9ft in
Maximum Depth Of Cut
0.8ft in
Maximum Lift Above Ground
2.7ft in
Width - Over End Bits
12.4ft in
Blade Tilt Angle - Right - Hydraulic
4.8 degrees
Blade Tilt Angle - Left - Hydraulic
5.5 degrees
Blade Tilt Adjustment - Right
1ft in
Blade Tilt Adjustment - Left
1.2ft in
Total Tilt Adjustment
2.2ft in
Width - Moldboard Length
12ft in
Cab - Standard
Machine Sound Level (Iso 6395) Tier 3/Stage Iiia Equivalent
112 dB(A)
Operator Sound Level - Iso 6396
71 dB(A)
Machine Sound Level (Iso 6395) Tier 4/Stage Iv
111 dB(A)
Cab - Suppression
Operator Sound Level - Iso 6396
70 dB(A)
Machine Sound Level (Iso 6395) Tier 4/Stage Iv
109 dB(A)
Machine Sound Level (Iso 6395) Tier 3/Stage Iiia Equivalent
110 dB(A)
